Very Good Resistance To Sagging And High Resistance To UV Radiation
Junbond® JB-16 is a silicone glass sealer that flows into hidden cracks and areas
that may be harder to reach. The sealant provides a tough,
waterproof, durable, and clear seal that will prove to be resistant
to different types of weather conditions, extreme temperatures,
vibrations and shocks, and even most chemicals.
Junbond® JB-16 Windshield Polyurethane Sealant an isocyanate-free, high modulus,non conductive, thixotropic,
single component modified polyurethane adhesive, which polymerizes
rapidly under the effect of atmospheric moisture. It has been
specially designed for bonding of fixed glass in automotive repair.
It allows a drive away time of 6 hours in vehicles with or without
*Providing the ambient temperature is at least 23°C and relative
humidity 50 %.
At lower temperatures and humidities drive away time will be
1.Bonding and sealing for the gap of joints of road, airport
runway, square, wall pipe, wharf, roof, underground garage and
2.Sealing for leakage of oil refinery and chemical plant.
3.Bonding and sealing for industrial floor, such as epoxy floor and
all kinds of paint surface.
4.Excellent bonding, sealing and repairing of various kinds of
materials, such as concrete building, wood, metal, PVC, ceramics,
carbon fiber, glass, etc.
- Suitable for applying to the opening of the windscreen made of
any material, including aluminum;
- Due to its high initial hardness and exceptionally strong binding
properties, no additional fixation of the glass is required;
- Very good resistance to sagging;
- Does not "reach" for the tool;
- High speed of polymerization;
- High shear strength and high shear modulus. Good elasticity even
after long-term use;
- Very low electrical conductivity;
- Good adhesion to the residual materials of the old adhesive
- High resistance to UV radiation;
- Excellent adhesion to glass, glass with a ceramic coating and to
a. Fast curing under room temperature, no sagging, solvent free
b. High bonding strength,
c. Good chemical and water resistance
d. No conductive
e. Excellent noise, vibration and impaction resistance
f. Automotive OEM quality
|Black, homogeneous paste|
|Sagging properties(mm) GB/T 13477.6|
|Tack free time②(min) GB/T 13477.5|
|Curing speed(mm/d) HG/T 4363|
|Non-volatile contents ( %) GB/T 2793|
|Shore A-hardness GB/T 531.1|
|Tensile strength(MPa) GB/T 528|
|Elongation at break(%) GB/T 528|
|Tear strength( N/mm) GB/T 529|
|Tensile-shear strength(MPa)GB/T 7124|
- 300ml aluminum tube
- 600ml in sausage
- 200L in barrel
Transport and storage
- Avoid eyes and skin connection. Operate at draughty place. Full
curing time is usually 24 hours, maybe longer at low temperature.
The surfaces to be bonded should be dry, clean without any grease,
dust or other contaminant. Further information could be get from
- Storage: Keep sealed into cool, dry place.
- Storage temperature: 5~25℃. Humidity: ≤50%RH.
- Cartridge and Sausage 9 month, Pail 6 month.
- Keep away from children.
- Avoid contacting with skin and eye. For skin contacted, remove the
sealant by cloth, wash skin thoroughly with soap and water. For eye
contacted, hold eyelids apart and flush thoroughly with water,
Clean before operation
Clean and dry all surfaces by removing foreign matter and
contaminants such as oil dust, grease,
frost, water, dirt, old sealants and any protective coating. Dust
and loose particles should be cleaned.
Direction of operation
Tool:Manual or pneumatic plunger caulking gun
>1. >Cut nozzle to give the required angle and bead size
2.Pierce the membrane at the top of the cartridge and screw on the
3.Place the cartridge in an applicator gun and squeeze the trigger
with equal strength
1.Obtain a new windshield.
2.Remove the plastic surround side and top mouldings correctly.
3.Cut the urethane from the outside between the glass and the
4.Apply a windshield primer to the frit band.
5.Apply the urethane with an electric caulking gun.
6.Lift the windshield into place.
7.Push the window down around the frame to guarantee a tight bond.
8.Allow the urethane to dry.
Junbom Hui Bei Factory
Package & Delivery
Q1. Do you have any MOQ limit for order?
A: Low MOQ, 3000pcs for order is availabl. And depend on your
Q2. Can I get samples to test before bulk order ?
A: Yes, we welcome sample order to test and check quality.
Q3. What about the lead time?
A:Sample needs 2-3 day, bulk production time around needs 1-2
weeks(the specific time depends on the number of orders.)
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by freight forwarding. It usually takes about
20---30 days to arrive. FCL and LCL, shipping can optional.
Q5. How to proceed an order for polyurethane sealant?
A:Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our
Thirdly customer confirms the samples and places deposit for formal
Fourthly We arrange the production.
If you want to know more details information, pls just feel free to
contact us! :)